Softwell Digital Practical Manual
Practical 01 - Create WinCC Unified Device
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Create WinCC Unified Device.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Create WinCC Unified Device | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Create WinCC Unified Device is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Talk to Automation Advisor
Get expert guidance for course selection, corporate training, project support and practical learning path.
Softwell Digital Practical Manual
Practical 02 - Connect PLC Tags
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Connect PLC Tags.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Connect PLC Tags | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Connect PLC Tags is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Skills & Tools You Will Learn
Important automation skills are arranged for job-level, project-level and Industry 4.0 learning.
Softwell Digital Practical Manual
Practical 03 - Create Main Screen
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Create Main Screen.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Create Main Screen | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Create Main Screen is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 04 - Add Navigation Buttons
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Add Navigation Buttons.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Add Navigation Buttons | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Add Navigation Buttons is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Why Choose Softwell Automation
Learn automation with practical examples, industrial troubleshooting approach and complete IT/OT learning path.
Softwell Digital Practical Manual
Practical 05 - Create Motor Control Faceplate
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Create Motor Control Faceplate.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Create Motor Control Faceplate | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Create Motor Control Faceplate is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Course Contents / Curriculum
The curriculum follows a practical sequence from fundamentals to project integration.
Softwell Digital Practical Manual
Practical 06 - Add Numeric IO Field
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Add Numeric IO Field.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Add Numeric IO Field | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Add Numeric IO Field is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Frequently Asked Questions About WinCC Unified SCADA Manual Unified HMI and SCADA Practical Manual
Who can join this training?
Students, freshers, working engineers, maintenance teams and corporate plant engineers can join based on their requirement.
Is practical training included?
Yes. The training is focused on PLC, SCADA, HMI, VFD, communication, troubleshooting and project based practice.
Can I request online or corporate training?
Yes. Softwell Automation provides classroom, online, corporate and in-plant training options.
Softwell Digital Practical Manual
Practical 07 - Create Alarm Classes
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Create Alarm Classes.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Create Alarm Classes | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Create Alarm Classes is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 08 - Configure Alarm View
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Configure Alarm View.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Configure Alarm View | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Configure Alarm View is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 09 - Create Trend Control
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Create Trend Control.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Create Trend Control | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Create Trend Control is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 10 - Configure Tag Logging
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Configure Tag Logging.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Configure Tag Logging | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Configure Tag Logging is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 11 - Recipe Screen Practical
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Recipe Screen Practical.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Recipe Screen Practical | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Recipe Screen Practical is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 12 - User Login and Roles
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for User Login and Roles.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | User Login and Roles | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
User Login and Roles is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 13 - Screen Popup Practical
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Screen Popup Practical.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Screen Popup Practical | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Screen Popup Practical is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 14 - Runtime Simulation
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Runtime Simulation.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Runtime Simulation | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Runtime Simulation is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 15 - Download Unified HMI
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Download Unified HMI.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Download Unified HMI | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Download Unified HMI is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 16 - Communication Diagnostics
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Communication Diagnostics.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Communication Diagnostics | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Communication Diagnostics is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 17 - Create Report Screen
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Create Report Screen.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Create Report Screen | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Create Report Screen is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 18 - Backup Unified Project
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Backup Unified Project.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Backup Unified Project | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Backup Unified Project is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 19 - Integrated PLC HMI Test
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Integrated PLC HMI Test.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Integrated PLC HMI Test | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Integrated PLC HMI Test is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Softwell Digital Practical Manual
Practical 20 - Final WinCC Unified SCADA Project
Philosophy: Open the software, open the Softwell manual, and perform the practical.
Setup: Engineering laptop, PLC tags or simulator, Unified runtime target
A. Step-by-Step Procedure
B. Verification Checklist
- The project/configuration completes without an unresolved compile or device error.
- Online, simulation or runtime values respond in the expected sequence for Final WinCC Unified SCADA Project.
- Critical addresses, parameters, units and initial states are checked against the lab sheet.
- The saved project can be reopened and the result reproduced without hidden manual correction.
C. If the Result Is Wrong
| Symptom | Probable cause | Diagnostic check | Corrective action |
|---|---|---|---|
| Compile or configuration error | Unresolved device, tag, type, address or parameter | Open the first diagnostic entry and trace it to the configured object | Correct the source item, compile again and save a new evidence record |
| No online/runtime response | Wrong connection, command source, permissions or scan state | Monitor live values from input through logic to output | Restore the verified connection/state and repeat one controlled test |
| Unstable or unexpected value | Scaling, initial state, timing or version mismatch | Compare raw and engineering values and review the installed version | Correct scaling/state, reset the lab safely and retest |
D. Student Evidence Record
Record software version, controller/device firmware, driver and license status.
Save the project/archive name, modified block/object and parameter list.
Capture a verified screenshot, trend, alarm, tag table or measured value.
Write the pass condition, fault tested, correction made and final observation.
| Practical | Final WinCC Unified SCADA Project | Pass condition | Observed result matches the stated objective and can be repeated. |
|---|---|---|---|
| Evidence filename | ________________ | Trainer / self-check | ________________ |
Expected Result
Final WinCC Unified SCADA Project is completed, verified and documented inside the WinCC Unified SCADA Manual workflow.
Before You Start: Prerequisites, Tested Version, Safety and Evidence
This manual is a practical training workbook, not a substitute for the installed product manual or the site's approved engineering procedure. Record the exact software, firmware, license and hardware before following a step because menus and supported functions can vary by release.
Tested-version planning scope: Confirm TIA Portal WinCC Unified V18 or V19, target panel or PC Runtime, browser, certificates and PLC firmware. Enter the exact lab-tested software, firmware and hardware in the record below before course delivery; never assume cross-version compatibility.
Software build, firmware, device catalog, driver, communication interface and license status.
Use an isolated training system. Follow electrical, mechanical, process and cybersecurity controls before energizing or downloading.
Keep the source project, parameter/code export, screenshot/trend, fault test, correction and final pass result.
Last reviewed by Softwell Automation Technical Training Team on 17 July 2026.
| Field | Learner record | Verification |
|---|---|---|
| Software / firmware | ________________ | Matches the training device and official compatibility information |
| Project / backup | ________________ | Saved before and after the practical |
| Pass evidence | ________________ | Runtime value, trend, alarm, diagnostic or report attached |
| Fault tested | ________________ | Symptom, cause, check and corrective action documented |
Practice, Viva and Extension Challenge
Change one approved input or parameter, predict the result, execute the test and explain any difference.
Explain the data flow, safety boundary, first diagnostic check and recovery method without opening the answer.
Add one useful function while preserving the original pass criteria, alarm behavior and rollback path.
Combine at least three practicals, submit a versioned project and evidence pack, and demonstrate repeatable recovery.
Content status: Substantively reviewed and expanded 17 July 2026. Verify release-specific details against the linked official documentation.